BOCA RESEARCH, INC. MULTIMEDIA MODEM FDV14I, MULTIMEDIA MODEM FDVV14I Card Type Modem (asynchronous) Chipset Rockwell I/O Options Microphone in, speaker out, voice Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, MNP10, V.42, V.42bis Fax Class Class I & II Data Bus 8/16 bit ISA Card Size Full height, half length [Image] CONNECTIONS Function Label Function Label Telephone line out CN1 Microphone in CN3 Telephone line in CN2 Speaker out CN4 INTERRUPT SELECTION Setting JP1/A JP1/B JP1/C JP1/D 3 Closed Open Open Open 4 Open Closed Open Open 5 Open Open Closed Open 7 Open Open Open Closed SERIAL PORT ADDRESS SELECTION Setting JP1/E JP1/F JP1/G JP1/H 3F8h (COM1:) Closed Open Open Open 2F8h (COM2:) Open Closed Open Open 3E8h (COM3:) Open Open Closed Open 2E8h (COM4:) Open Open Open Closed SUPPORTED STANDARD COMMANDS Basic AT Commands +++, A/ A, C, E, H, L, M, N, O, Q, V, W, X, Y, Z &C, &D, &F, &K, &P, &Q, &S, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \G, \K, \L, \N, \W %C, %E, %F, %L, %Q Special AT Commands *H S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S14, S16, S18, S21, S22, S24, S25, S26 S27, S30, S32, S33, S38, S46, S48, S82, S86, S91, S92, S95 Note: See MHI help file for complete information. UNIDENTIFIED COMMANDS Command Default S23 7 S28 Unidentified S36 Unidentified S39 Unidentified S40 Unidentified S41 Unidentified Proprietary AT Command Set DIAL Type: Immediate Format: AT [cmds] D<#>;[cmds] Description: Dials the telephone number indicated according to any modifiers included in the string. Command Function DL Re-dial last number. DP Pulse dialing enabled. DS=n Dial stored telephone number n. DT Tone dialing enabled. DW Dialing resumed following dial tone detection. D, Dialing paused for amount of time specified in S8 register. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D^ Disable calling tone for this call. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DISPLAY INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested about the modem. Command Function I0 Displays product identification code. I1 Displays ROM checksum. I2 Tests and displays ROM checksum result. I3 Displays firmware revision. LINE SPEED Type: Register Format AT [cmds] S37=n [cmds] Description: Sets the maximum connect speed attempted during handshake process. Command Function S37=0 Auto-detect the highest common connect speed. S37=1 Attempt to connect at 300bps. S37=2 Attempt to connect at 300bps. S37=3 Attempt to connect at 300bps. S37=5 Attempt to connect at 1200bps. S37=6 Attempt to connect at 2400bps. S37=7 Attempt to connect with V.23 at 1200/75bps. S37=8 Attempt to connect at 4800bps. S37=9 Attempt to connect at 9600bps. S37=10 Attempt to connect at 12Kbps. S37=11 Attempt to connect at 14.4Kbps. S37=12 Attempt to connect at 7200bps. PROTOCOL/SPEED Type: Configuration Format: AT [cmds] Fn [cmds] Description: Selects the protocol and speed the modem will attempt to connect at. Command Function F0 Auto-detect the highest common connect speed. F1 Select V.22 or Bell 212A at 1200bps speed. F3 Select V.23 at 75/1200bps speed. F4 Select V.22bis at 2400bps speed. F6 Select V.32 or V.32bis at 4800bps speed. F7 Select V.32bis at 7200bps speed. F8 Select V.32bis or V.32 at 9600bps speed. F9 Select V.32bis at 12Kbps speed. F10 Select V.32bis at 14.4Kbps speed.